This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.ĬOMPLIANCES CE Mark Declaration of Conformance for EMI and Safety (EEC) SMC contact for these products in Europe is: SMC Networks Europe, Edificio Conata II, Calle Fructuós Gelabert 6-8, 2o, 4a, 08970 - Sant Joan Despí, Barcelona, Spain.ĬOMPLIANCES Safety Compliance Warning: Fiber Optic Port Safety CLASS I LASER DEVICE When using a fiber optic port, never look at the transmit laser while it is powered on. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.ĬOMPLIANCES FCC - Class A This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. LIMITED WARRANTY WARRANTIES EXCLUSIVE: IF AN SMC PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, CUSTOMER’S SOLE REMEDY SHALL BE REPAIR OR REPLACEMENT OF THE PRODUCT IN QUESTION, AT SMC’S OPTION. SMC may, at its own discretion, repair or replace any product not operating as warranted with a similar or functionally equivalent product, during the applicable warranty term. All SMC products carry a standard 90-day limited warranty from the date of purchase from SMC or its Authorized Reseller. (“SMC”) warrants its products to be free from defects in workmanship and materials, under normal use and service, for the applicable warranty term. LIMITED WARRANTY Limited Warranty Statement: SMC Networks, Inc. 20 Mason Irvine, CA 92618 All rights reserved. SMC reserves the right to change specifications at any time without notice. No license is granted by implication or otherwise under any patent or patent rights of SMC. However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. (SMC) is believed to be accurate and reliable. Information furnished by SMC Networks, Inc. I'm just not sure what I have configured incorrectly.Īny help that anybody here can provide would be greatly appreciated.USER GUIDE ta SMCGS24C-Smart EZ SwitchTM 10/100/1000 24-Port Smart SwitchĮZ Switch 10/100/1000 User Guide From SMC’s EZ line of cost-effective workgroup LAN solutions 20 Mason Irvine, CA 92618 Phone: (949) 679-8000 March 2008 Pub. I'm pretty sure my settings on this page are where my problem lies. Ports 7-26 are for service systems on VLAN ID 1002 Ports 3-6 are for internal business computers on VLAN ID 1001 Port 2 is connected to the Router (on Router LAN Port 2) Port 1 is intended to be a management port ![]() VLANs are configured as described in the VLAN section above My end goal is to have ports 3-6 on VLAN ID 1001 and have the router automatically assign an IP in the 192.168.0.x range and for connections on ports 7-26 on VLAN ID 1002 with the router automatically assigning in the IP range of 192.168.1.X range. If I connect to any of the other ports I am unable to get an IP address assigned from the router. VLAN ID 1002 DHCP is set to assign 192.168.1.XĬurrently I am able to connect on ports 1 and 2 of the switch on the default VLAN ID 1 and get IP addresses automatically assigned in the range. VLAN ID 1001 DHCP is set to assign 192.168.0.X VLANs are configured as described in the VLAN information above. VLAN ID 1001 is for internal business computers I am new to VLANs and I think I am just having a mental block with the terminologies that SMC uses. I am now trying to do the same with the SMC managed switch, but I am running into a wall with it. So far I have been able to get the Router and WAP to separate connected devices into their appropriate VLANs based on the SSID that the client system connects to. My goal is to have 2 separate VLANs, one for internal business computers and one for computers being serviced so that I can have the service computers connect to the internet without having access to my business' systems. I am in the process of configuring a new network layout for my computer repair business using a Cisco RV320 Router, SMC SMCGS26C-Smart managed switch and a D-Link DAP-2660 WAP.
0 Comments
Leave a Reply. |